RUT955
RUT955

RUT955

97140001

Robusto enrutador celular profesional Dual SIM 4G / LTE y WiFi. Este dispositivo industrial altamente seguro y confiable está equipado con Ethernet, E / S digitales y analógicas, RS232, RS485, GNSS (GPS), microSD y USB. 

Las interfaces Ethernet, digitales y analógicas, RS232, RS485, GNSS (GPS), microSD y USB permiten una increíble variedad de escenarios de aplicaciones industriales.

Está equipado con redundancia de conectividad a través de conmutación por error Dual SIM.

Viene con RutOS, que está repleto de funciones de software avanzadas, como Modbus, SNMP, TR-069, NTRIP, MQTT y múltiples servicios VPN.

LTE Cat 4 con velocidades de hasta 150 Mbps

Dual SIM: reduce significativamente los costos de roaming

Posicionamiento GNSS con funcionalidad de geofencing

Interfaces de comunicación serie RS232 / RS485

Múltiples entradas / salidas para monitoreo y control remoto

Compatible con el sistema de gestión remota Teltonika

Robusto enrutador celular profesional Dual SIM 4G / LTE y WiFi. Este dispositivo industrial altamente seguro y confiable está equipado con Ethernet, E / S digitales y analógicas, RS232, RS485, GNSS (GPS), microSD y USB.

RUT955 es un enrutador 4G / LTE altamente confiable y seguro con E / S, GNSS y RS232 / RS485 destinados a aplicaciones profesionales. El dispositivo ofrece capacidades de localización de GPS y comunicación celular de misión crítica de alto rendimiento y está equipado con redundancia de conectividad a través de conmutación por error Dual-SIM. Los conectores de antena externa permiten conectar las antenas deseadas y encontrar fácilmente la mejor ubicación de señal.

PRODUCT  
Model/Part# See table below for full set of Model and Part Numbers
SPECTRUM  
Channel Spacing Configurable on 5 MHz increments
Frequency Range 5150 - 5970 MHz (exact frequencies as allowed by local regulations) 
Channel Width 5 I 10 I 20 I 40 MHz
INTERFACE  
MAC (Media Access Control) Layer Cambium proprietary and optionally standard 802.lln
Physical Layer 2x2 MIMO/OFDM
Ethernet Interfaced 100/lOOOBaseT, rate auto negotiated, 802.3at compliant
Powering Methods Supported 56 V PoE (included), standard 802.3at PoE Supply, or CMM4 with 56 V and 5 pin to 7 pin cross over cable adapter
Protocols Used IPv4/IPv6 (Dual Stack), UDP, TCP, ICMP, SNMPv2c, NTP, STP, IGMP, SSH
Network Management IPv4/IPv6, HTTPs, SNMPv2c, SSH, Cambium Networks CnMaestro™
VLAN 802.lQ with 802.lp priority
PERFORMANCE  
Subscribers per Sector Up to 120; Lite version limited to 10
ARQ Yes
Nominal Receive Sensitivity (w/FEC) @20MHz Channel MCSO = -93 dBm to MCS15 = -69 dBm (per branch)
Nominal Receive Sensitivity (w/FEC) @40MHz Channel MCSO = -90 dBm to MCS15 = -66 dBm (per branch)
Modulation Levels (Adaptive) MCSO (BPSK) to MCS15 (640AM 5/6)
GPS Synchronization Yes, via internal GPS or CMM4 with 56 V and 5 pin to 7 pin cross over cable adapter
Quality of Service Three-level priority (Voice, High, Low) with packet classification by DSCP, COS, VLAN ID, IP & MAC Address, Broadcast, Multicast, 
and Station Priority
Transmit Power Range 0 to +30 dBm (combined, to regional EIRP limit) (1 dB interval)
RECOMMENDED ANTENNAS  
Sector Antenna ePMP Sector Antenna (C050900D021A) available
ePMP 2000 Smart Antenna ePMP 2000 Smart Antenna (C050900D020A) available (complimentary; does not replace Sector Antenna)
PHYSICAL  
Sector Antenna Connection 2 x 50 ohm, RP (reverse polarity) SMA
Beamforming Antenna Connection 2 x 50 ohm, RP (reverse polarity) SMA, DC coupled (powering antenna)
GPS Antenna Connection 1 x 50 ohm, RP (reverse polarity) SMA
Surge Suppression 1 Joule Integrated
Environmental IP55
Temperature -30°C to +55°C (-22°F to +131°F)
Power Consumption 20 W Maximum [1]
Input Voltage 44 V to 59 V
Weight 0.7 kg (1.54 lbs.) without brackets
Dimensions 125 x 210 x 37 mm (4.9 x 8.3 x 1.5 in.) without brackets
Pole Mount Included Yes
Environmental Cover Included Yes
SECURITY  
Encryption 128 bit AES (CCMP mode)
CERTIFICATIONS  
FCCID Z8H80FT0020
Industry Canada Cert 109W-0020
CE

EN 301 893 V2.1.1  

EN 302 502 V2.1.1

Notes:
[1] The maximum power consumption of the Access Point is the same regardless of whether the optional Smart
Beamforming Antenna is equipped or not. This is because the Beamforming Antenna draws its power during the uplink
cycle when the Access Point power consumption is not at its maxium.

Artículos relacionados